Rework procedure
From PlcWiki
Petr.zalabak (Talk | contribs) (Created page with 'Generally a rework procedure can be done either on a dedicated Rework station or directly on an assembly line. The product is marked as reworked using a control barcode "Sen…') |
Petr.zalabak (Talk | contribs) |
||
| Line 1: | Line 1: | ||
Generally a rework procedure can be done either on a dedicated [[Rework station]] or directly on an assembly line. | Generally a rework procedure can be done either on a dedicated [[Rework station]] or directly on an assembly line. | ||
| - | The product is marked as reworked using a control barcode "Send to rework (PLCSENDREW)". It is possible to remove the rework attribute using a barcode "Remove rework (PLCRMREW)". | + | The product is marked as reworked using a control barcode "Send to rework (PLCSENDREW)". It is possible to remove the rework attribute using a barcode "Remove rework" (PLCRMREW) or "Rework finished" (PLCFINREW). |
There are several parameters in a client configuration file which define the behavior to the reworked products: | There are several parameters in a client configuration file which define the behavior to the reworked products: | ||
| - | |||
== Second loop of reworked products == | == Second loop of reworked products == | ||
| Line 10: | Line 9: | ||
When during its assembly the cockpit is found to be reworked, it is marked using a barcode "Send to rework (PLCSENDREW)". Such a product is not deleted from the kernel data when it passes the final station and the product will go the second loop on an assembly line. It is not shown in the product sequence on the client screen, but when it is scanned on any workstation, it is automatically recognized as reworked. The following settings is needed to suppress the error message "Sequence error". Client version 1203091815 or higher is needed. | When during its assembly the cockpit is found to be reworked, it is marked using a barcode "Send to rework (PLCSENDREW)". Such a product is not deleted from the kernel data when it passes the final station and the product will go the second loop on an assembly line. It is not shown in the product sequence on the client screen, but when it is scanned on any workstation, it is automatically recognized as reworked. The following settings is needed to suppress the error message "Sequence error". Client version 1203091815 or higher is needed. | ||
WorkPlace.ReworkedProductOutOfSequence = '''No''' | Yes | WorkPlace.ReworkedProductOutOfSequence = '''No''' | Yes | ||
| + | |||
| + | == Complete rework procedure on a standard assembly workstation == | ||
| + | Normally the reworked products can be processed on assembly workstations incompletely. It means it is not necessary to complete the whole procedure for these products. They are reworked, so maybe some operations are already done and it is not necessary to repeat them. | ||
| + | |||
| + | But for some workstations or production lines the full procedure is requested. It is possible to set it using the following parameter: | ||
| + | workplace.InCompleteReworkOnWSAllowed = No | '''Yes''' | ||
| + | If this parameter is set to "No", the reworked products needs to be completely finished on the workstation. | ||
| + | I.e. they have the same logic like the normal ones. Otherwise, reworked products can be interrupted by | ||
| + | a scanning of the next product ID any time. | ||
| + | |||
| + | == Sequence Check For All Reworked Products == | ||
| + | If the following parameter is set to "Yes", the reworked products needs to be processed on the workstation. | ||
| + | I.e. they have the same logic like the normal ones and are requested in the correct position in the sequence | ||
| + | even the rework procedure was completely finished (for example on a rework station). This setting is used mainly on the very last station, if it is necessary to check the correct sequence of all finished product. | ||
| + | workplace.SequenceCheckForAllReworkedProducts = '''No''' | Yes | ||
Revision as of 08:57, 30 March 2012
Generally a rework procedure can be done either on a dedicated Rework station or directly on an assembly line.
The product is marked as reworked using a control barcode "Send to rework (PLCSENDREW)". It is possible to remove the rework attribute using a barcode "Remove rework" (PLCRMREW) or "Rework finished" (PLCFINREW).
There are several parameters in a client configuration file which define the behavior to the reworked products:
Second loop of reworked products
When during its assembly the cockpit is found to be reworked, it is marked using a barcode "Send to rework (PLCSENDREW)". Such a product is not deleted from the kernel data when it passes the final station and the product will go the second loop on an assembly line. It is not shown in the product sequence on the client screen, but when it is scanned on any workstation, it is automatically recognized as reworked. The following settings is needed to suppress the error message "Sequence error". Client version 1203091815 or higher is needed.
WorkPlace.ReworkedProductOutOfSequence = No | Yes
Complete rework procedure on a standard assembly workstation
Normally the reworked products can be processed on assembly workstations incompletely. It means it is not necessary to complete the whole procedure for these products. They are reworked, so maybe some operations are already done and it is not necessary to repeat them.
But for some workstations or production lines the full procedure is requested. It is possible to set it using the following parameter:
workplace.InCompleteReworkOnWSAllowed = No | Yes
If this parameter is set to "No", the reworked products needs to be completely finished on the workstation. I.e. they have the same logic like the normal ones. Otherwise, reworked products can be interrupted by a scanning of the next product ID any time.
Sequence Check For All Reworked Products
If the following parameter is set to "Yes", the reworked products needs to be processed on the workstation. I.e. they have the same logic like the normal ones and are requested in the correct position in the sequence even the rework procedure was completely finished (for example on a rework station). This setting is used mainly on the very last station, if it is necessary to check the correct sequence of all finished product.
workplace.SequenceCheckForAllReworkedProducts = No | Yes
